Omron GX-AD0471 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 394

Omron GX-AD0471 Скачать руководство пользователя страница 63

4 - 15

4 Installation and Wiring

GX-series EtherCAT Slave Unit User’s Manual

4-4
Con

n

ect
ing
an Ext

er

n

al Dev

ice

4

4-

4-2 C

onnecting to

e-CON Co

nnect

or
Ter

m

ina
ls



Using Tyco Electronics, Sumitomo 3M or Panasonic Electric Works
connectors

Cables of connected devices are normally cut in semi-strip or strip specification as shown in the next
figures.

When the cables are prepared this way, an e-CON connector cannot be attached. First cut the end
and remove the cable sheath as shown in the following diagram. (Do not strip the sheaths of the
core wires.)



Using OMRON connectors

Align the cable with the STRIP GAUGE described on the side of the connector. Remove 7 to 8 mm
of the wiring sheath, and twist the exposed wires several times.

Processing external devices cables

Semi-strip specification

Strip specification

20 mm min.

Core wires

Strip sheaths of core wires

7 to 8 mm

«
...
61
62
63
64
65
...
»

Содержание GX-AD0471











































































































































































































































































































































































































Отзывы:

Нет отзывов