ODA EX 100-12 Скачать руководство пользователя страница 29

Страница: 29 / 94

3-4. Programming Over Voltage Protection(OVP)

Overvoltage protection guards the load against output voltages that reach a specified value greater

than the programmed protection level. Below procedure is for setting the OVP level.

disable the OVP at the Factory Mode.

▌

Turn on the power supply

After turned on, check the power supply displays"**OUTPUT OFF**" Mode.

▌

Press the "Protection" key in other to enter the OVP menu

LCD Display

PROTECT> 1.OVP

▌

Press the "Protection" key one more time at the "1.OVP" state.

LCD Display

OVP SET> 32.00V

▌

Move the under bar cursor location where you want to change.

▌

Set the trip level.

Note that you cannot set the trip levels to lower than current real

output volt in order to prevent the operator's malfunction occurring.

▌

After set the trip levels that you want, press the "Protection" Key.

CHANGED

After displayed above message, The power supply will exit the OVP menu

and the display will return to the meter mode.

Cancelling

▌

If you don't want to change the OVP levels, just wait during 5 seconds.

Wait 5 sec

LCD Display

CANCEL…

≫ Related Remote Interface Command

VOLT:OVP {<voltage>}
VOLT:OVP?
VOLT:TRIP?
VOLT:CLE

Refer: VOLT:OVP 25

Set the OVP Level

VOLT:OVP?

Confirm the OVP Level

VOLT:OVP:TRIP?

Confirm tripped OVP

VOLT:OVP:CLE

Clear tripped OVP

About initial OVP setting, refer to Default Setting Values of "1-6. Check After Power On"

Note

- 30 -

LCD Display

Содержание EX 100-12































































































Результаты поиска

Содержание EX 100-12

Отзывы:

Похожие инструкции для EX 100-12

Бренды по названию

Популярные бренды

ODA EX 100-12, Руководство пользователя

Результаты поиска

Содержание EX 100-12

Отзывы:

Похожие инструкции для EX 100-12

Бренды по названию

Популярные бренды