ODA EX 100-12 Скачать руководство пользователя страница 26

Страница: 26 / 94

3-2. Constant Current Operating (CC)

To set up the power supply for constant current (CC) operation, proceed as follows

▌

Turn on the power suppl

After turned on, check the power supply displays"**OUTPUT OFF**" Mode.

▌

Connect the DUT to output terminals.

▌

In order to set the limit value, press the LMT Key.

▌

Press the left key and move the under bar cursor to voltage value. In order to

increase or decrease the voltage value, turn the encoder switch CW or CCW.

Under the protection(OVP/UVL/OVL) setting state, voltage ca nnot be over

protection level. If the voltage value is over the protect ion setting value,

instrument "displays "PROTECTION LIMIT" message and volta ge will set to

protection level value

▌

In other to set the current value, use the right cursor key and encoder knob.

Under the protection(OVP/UVL/OVL) setting state, current ca nnot be over

protection level. If the voltage value is over the protect ion setting value,

instrument "displays "PROTECTION LIMIT" message and curre nt will set to

protection level value.

▌

If the all setting is finished, enable the output.(Press the output ON/OFF key

and then power supply changes to readback display from limit display

▌

CC lamp is on, CV lamp is off.

If lamp is reversed, check the voltage setting value is low.

If the voltage value is low, increase the current value limit.

≫ Related Remote Interface Command

APPLy{<voltage>,<current>}

VOLT{<voltage>|UP|DOWN}

CURR{<current>|UP|DOWN}

OUTP{OFF|ON}

OUTP OFF

Disable Output

Apply 2:

OUTP OFF

VOLT 10

Set the voltage to 10V

APPLY 10,5

Set 10

10V /5A

CURR 5

Set the current 5A

OUTP ON

Enable Output

- 27 -

Disable Output

Enable Output

Apply 1:

Содержание EX 100-12































































































Результаты поиска

Содержание EX 100-12

Отзывы:

Похожие инструкции для EX 100-12

Бренды по названию

Популярные бренды

ODA EX 100-12, Руководство пользователя

Результаты поиска

Содержание EX 100-12

Отзывы:

Похожие инструкции для EX 100-12

Бренды по названию

Популярные бренды