ODA EX 100-12 Скачать руководство пользователя страница 57

Страница: 57 / 94

Voltage Calibraton

▌

Turn off all device and connect all device before calibration

>Connect the power supply (+) output bus bar at the DVM (+) and connect
the power supply (-) output bus bar at the DVM (-)

▌

Turn on Power switch in a pessing calibration key .

▌

Power switch on.

▌

After self test is finished, and when appearing "1.cal-volt low" message,

release calibration key.

▌

Press the calibration key in "1.cal-volt low" mode.

LCD Display

V-LOW 00.14V

Display value can be different

Wait for 5 minute

▌

Wait until DVM display voltage becomes stable

▌

Enters a voltage value that you obtained by reading an external DVM meter.

If the value is 151.9mV, enters as following below.

LCD Display

V-LOW 00.15V

This is an examples for 30V.

▌

After finished to enter the value, press the "Calibration" key.

LCD Display

ADC datA 026ch

About 500ms, display HEX value instead

of readback value.

LCD Display

1.cal-volt low

Return to the previous state of calibration

Move to "2.cal-volt high" mode by using cursor key and press the "Calibration" key.

LCD Display V-high 31.60V

Display voltage value can be different

Wait for 5 minute

▌

Wait until DVM display voltage becomes stable

- 58 -

Содержание EX 100-12































































































Результаты поиска

Содержание EX 100-12

Отзывы:

Похожие инструкции для EX 100-12

Бренды по названию

Популярные бренды

ODA EX 100-12, Руководство пользователя

Результаты поиска

Содержание EX 100-12

Отзывы:

Похожие инструкции для EX 100-12

Бренды по названию

Популярные бренды