ODA EX 100-12 Скачать руководство пользователя страница 19

Страница: 19 / 94

12. Volt Cursor or Menu Change Key.

Move the under bar digit to the left about voltage. It also is used to move to next menu

when selected menu mode.

13. Curr Cursor or Menu Change Key.

Move the under bar digit to the right about current. It also is used to move to next menu

when selected menu mod

14. Output ON/OFF Key.

Enables or disables the power supply output. This key toggles between on and off

15. IO/Local Setting and Error Display Key

Configures the power supply for remote interfaces(Choose RS232C, RS485 or TCP/IP)

This key can be used to change to Local Mode from Remote Interface state.

Displays error codes generated during operation and self-test. Automatically convert to IO/Local key.

16. Protection setting and Front-panel Lock Key

Enables or disables the OVP/OCP/UVL/OVL/UCL/OCL protection function, sets trip voltage level,

and clears the over-voltage condition. Also press this key for 1sec, you can lock front panel operating

with lighting LOCK lamp. Press agaoin this key for 1 sec, clear the lock key.

17. Volt/Curr Setting Limit Display Key

Shows setting value of voltage and current and allows knob adjustment for setting limit values

with lighting LMT lamp. press again this key for 1 sec, return to previous state.

You only see the setting value not just real output value.

18. Store or Calibration Key.

Stores an operating state(voltage, current, OVP, OCP and other state) in location ‘‘1’’, ‘‘2’’,
‘‘3’’ or another number / enables calibration mode with pressing this key and put the AC power on.

19. Recall or Factory Key

Recalls an operating state(voltage, current, OVP, OCP and other state) in location ‘‘1’’, ‘‘2’’, ‘‘3’’ or

another number/ enables factory mode(Memory Initializing, ,Auto Cursor Move, Auto Key Lock,

OVP Disable, OCP Disable, ADC Sampling, Calibration Restore, Calibration Backup,

Calibration Factory Default Recover and etc) with pressing this key and put the AC power on

- 20 -

Содержание EX 100-12































































































Результаты поиска

Содержание EX 100-12

Отзывы:

Похожие инструкции для EX 100-12

Бренды по названию

Популярные бренды

ODA EX 100-12, Руководство пользователя

Результаты поиска

Содержание EX 100-12

Отзывы:

Похожие инструкции для EX 100-12

Бренды по названию

Популярные бренды