ODA EX 100-12 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 94

background image

If the real output current is higher than OCP level value, "OCP TRIPPED" message appears on the display.
And output voltage and current is dropped to near zero. In order to output the voltage and current,
at first remove the DUT from load wire and clear the tripped OCP as like below method.
The reason of tripped OCP occuring,

First, OCP setting level is lower than rear output current level. Therefore, increase the OCP level

Second, Maybe the DUT is like a coil, motor and as like a source that make an in rush current.

To avoid this, a UF-diode must be connected in series with the output as shown below.

Third, In case of using the DUT as like source. If external voltage source such as a battery

is connected across the output, feedback current level is higher than OCP level and it occurs
tripped OCP. A diode must be connected in series with the output as shown below.

Forth, If you can't control the tripped OCP, turn off the OCP function.

Enter the "Factory mode" and move to "6.OCP USE" and then disable this function.

▌

When occurs OCP trip, "OCP TRIPPED" message appears on the display

▌

In order to clear tripped OCP, increase the OCP Level.

LCD Display

Protect> 1.ovp

▌

Press the right cursor key in other to enter the OCP.

LCD Display

PROTECT> 2.OCP

▌

In the "protect> 2.ocp ", press the "Protection" key one more time.

LCD Display

OcP SET> 50.00a

▌

Move the under bar cursor where you want to change the level.

▌

Re-adjust the OCP level by using the encoder knob.

▌

Finished to change the level, press the "Protection" key.

LCD Display

CHANGED

After displayed above message, return to before state that tripped OCP.

≫ Related Remote Interface Command

CURR:OCP {<current>}
CURR:OCP?
CURR:OCP:TRIP?
CURR:OCP:CLE

Apply 1: Method of checking tripped OCP or not, Re-adust OCP Level.

CURR:OCP:TRIP? Return value "1"

Check the tripped OCP Trip

CURR:OCP 80

Set OCP Level

CURR:OCP:CLE

Clear OCP Trip

Apply2:

Method of checking tripped OCP or not, decrease current Level

CURR:OCP:TRIP? Return value "1"

Check the tripped OCP Trip

CURR 0

Set current to 0A

CURR:OCP:CLE

Clear OCP Trip

- 34 -

«
...
31
32
33
34
35
...
»

Содержание EX 100-12































































































Отзывы:

Нет отзывов

Похожие инструкции для EX 100-12

Бренд: MAKER MADE Страницы: 14

Бренд: National Flooring Equipment Страницы: 44

Бренд: Earlex Страницы: 12

Бренд: Earlex Страницы: 12

Бренд: Earlex Страницы: 4

Бренд: Earlex Страницы: 4

Бренд: Park Tool Страницы: 2

GEN 1500W SERIES

Бренд: Genesys Страницы: 76

Бренд: TDK-Lambda Страницы: 31

Бренд: Parkside Страницы: 103

Бренд: SilverBolt Страницы: 9

Бренд: Omer Страницы: 2

Бренд: Parkside Страницы: 100

X-Finity Series

Бренд: Ultra Products Страницы: 1

Бренд: Hander Страницы: 38

Бренд: Matrix Страницы: 46

Бренд: Pulsar Страницы: 3

Бренд: Matco Tools Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды