manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 624

FlexCAN Module

MCF5253 Reference Manual, Rev. 1

25-8

Freescale Semiconductor

 

25.5.2

FlexCAN Control Register (CANCTRLn)

CANCTRL

n

 is defined for specific FlexCAN control features related to the CAN bus, such as bit-rate, 

programmable sampling point within an Rx bit, loop back mode, listen-only mode, bus off recovery 
behavior, and interrupt enabling. It also determines the division factor for the clock prescaler. Most of the 
fields in this register should only be changed while the module is disabled or in freeze mode. Exceptions 
are the BOFFMSK, ERRMSK, and BOFFREC bits, which can be accessed at any time.

25

SOFTRST

Soft reset. When set, the FlexCAN resets its internal state machines (sequencer, error counters, error flags, and 
timer) and the host interface registers (CANMCRn [except the MDIS bit], TIMER, ERRCNT, ERRSTAT, IMASK, and 
IFLAG).
The configuration registers that control the interface with the CAN bus are not changed (CANCTRLn, RXGMASKn, 
RX14MASKn, RX15MASKn). Message buffers are also not changed. This allows SOFTRST to be used as a debug 
feature while the system is running.
Since soft reset is synchronous and has to follow a request/acknowledge procedure across clock domains, it may 
take some time to fully propagate its effect. The SOFTRST bit remains set while reset is pending and is 
automatically cleared when reset completes. The user should poll this bit to know when the soft reset has 
completed.
0 Soft reset cycle completed
1 Soft reset cycle initiated

24

FRZACK

Freeze acknowledge. Indicates that the FlexCAN module has entered freeze mode. The user should poll this bit 
after freeze mode has been requested, to know when the module has actually entered freeze mode. When freeze 
mode is exited, this bit is cleared once the FlexCAN prescaler is enabled. This is a read-only bit.
0 The FlexCAN has exited freeze mode and the prescaler is enabled.
1 The FlexCAN has entered freeze mode, and the prescaler is disabled.

23

SUPV

Supervisor/user data space. Places the FlexCAN registers in either supervisor or user data space. 
0 Registers with access controlled by the SUPV bit are accessible in either user or supervisor privilege mode.
1 Registers with access controlled by the SUPV bit are restricted to supervisor mode.

22–21

Reserved, should be cleared.

20

LPMACK

Low power mode acknowledge. Indicates that FlexCAN is disabled. Disabled mode cannot be entered until all 
current transmission or reception processes have finished, so the CPU can poll the LPMACK bit to know when the 
FlexCAN has actually entered low power mode. See 

Section 25.3.2.3, “Module Disabled Mode”

 for more 

information. This bit is read-only.
0 FlexCAN not disabled.
1 FlexCAN is in disabled mode.

19–5

Reserved, should be cleared.

5–0

MAXMB

Maximum number of message buffers. Defines the maximum number of message buffers that will take part in the 
matching and arbitration process. The reset value (0x1F) is equivalent to 32 message buffer (MB) configuration. 
This field should be changed only while the module is in freeze mode.
Note:

Table 25-2. FlexCAN Configuration Register (CANMCRn) Field Descriptions (continued)

Field

Description

Maximum MBs in Use = MAXMB + 1

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды