manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 392

Background Debug Mode (BDM) Interface

MCF5253 Reference Manual, Rev. 1

20-22

Freescale Semiconductor

 

Operand Data:

None

Result Data:

The “command complete” response, $FFFF (with the status bit cleared), is returned during the next shift 
operation.

20.3.4.1.9

Read Control Register (RCREG)

RCREG reads the selected control register and returns the 32-bit result. Accesses to the processor/memory 
control registers are always 32 bits in size, regardless of the implemented register width. The second and 
third words of the command effectively form a 32-bit address used by the debug module to generate a 
special bus cycle to access the specified control register. The 12-bit Rc field is the same as that used by the 
MOVEC instruction.

Figure 20-20. RCREG Command/Result Formats

Rc encoding:

 

Table 20-14. Control Register Map

Rc

Register Definition

$002

Cache Control Register (CACR)

$004

Access Control Register 0 (ACR0)

$005

Access Control Register 1 (ACR1)

$801

Vector BASE Register (VBR)

$804

MAC Status Register (MACSR)

$805

MAC Mask Register (MASK)

$806

MAC Accumulator (ACC0)

$807

MAC Accumulator (ACC1)

$808

MAC Accumulator (ACC2)

$80B

MAC Accumulator (ACC3)

$80E

Status Register (SR)

$80F

Program Register (PC)

$C04

RAM Base Address Register (RAMBAR0)

$C05

RAM Base Address Register (RAMBAR1)

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды