manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 326

Audio Interface Module (AIM)

MCF5253 Reference Manual, Rev. 1

17-28

Freescale Semiconductor

 

17.7.2

Data Exchange Register Overview

•

PDOR1-L, PDOR1-R: (Processor Data Out 1). These are 32-bit registers. Both registers have 4 
consecutive longword addresses assigned (multiple decode). This allows easy transfer of multiple 
samples using MOVEM instructions. Data written to these registers will end in one of the FIFO ‘s 
(

Figure 17-1

) 

12, 14, 17, 17a, 17b 

or 

25

. The format of data in the registers is defined below.

•

PDOR2-L, PDOR2-R: (Processor Data Out 2). Same function as PDOR1. Both (PDOR2-L and 
PDOR2-R) registers occupy 4 consecutive longword addresses (multiple decoded.) Data written to 
it will end in one of the FIFO ‘s. (fig. 17-1) 

12,14,17, 17a, 17b 

or 

25

.

•

PDOR3: (Processor Data Out3). Same function as PDOR1. But it is a single 32-bit register which 
contains both Left + Right data in 16-bit precision occupying 4 consecutive longword addresses. 
Data written to it will end in one of the FIFO ‘s. (fig 17-1) 

12,14, 17a, 17b 

or 

25

. 

•

PDIR1-L, PDIR1-R (Processor data in). Used to transfer data to the processor. These 32-bit 
registers, each occupy 4 consecutive longword addresses are used to read data from the audio bus. 

0x34
0x38

0x3C

0x40

PDOR1-L

32

Processor data out 1 Left.
Multiple address to write this register allows MOVEM instruction to write FIFO.

undef

W

0x44
0x48

0x4C

0x50

PDOR1-R

32

Processor data out 1 Right
Multiple address to write this register allows MOVEM instruction to write FIFO

undef

W

0x54
0x58

0x5C

0x60

PDOR2-L

32

Processor data out 2 Left
Multiple address to write this register allows MOVEM instruction to write FIFO

undef

W

0x64
0x68

0x6C

0x70

PDOR2-R

32

Processor data out 2 Right
Multiple address to write this register allows MOVEM instruction to write FIFO

undef

W

0x74
0x78

0x7C

0x80

PDOR3

32

Processor data out 3 left + right

undef

W

0x74
0x78

0x7C

0x80

PDIR2

32

Processor data in 3 left + right

undef

R

1

Multiple addresses for PDOR/PDIR fields are intended for easy use of MOVEM instruction to move data into and out of the FIFOs. 
The data read at each address of any range is exactly the same, being the next sample in/out of the FIFO. There is no difference 
in FIFO operation between a read at address e.g. 0x74, 0x78, 0x7C.

2

There are memory overlaps between PDIR’s and PDOR’s. PDOR’s cannot be read, PDIR cannot be written.

Table 17-14. Data Exchange Register Descriptions (continued)

Address

MBAR2 +

Name

Width

Description

1, 2

Reset

Value

Access

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды