NXP Semiconductors MCF5253 Скачать руководство пользователя страница 192 | Manualshive

Страница: 192 / 648

NXP Semiconductors MCF5253 Скачать руководство пользователя страница 192

General Purpose Timer Modules

MCF5253 Reference Manual, Rev. 1

11-6

Freescale Semiconductor

11.6.5

Timer Initialization Example Code

There are two timers on the MCF5253. With a 70 MHz clock, the maximum period is 3.83 seconds and a
resolution of 14.3 ns. The timers can be free running or count to a value and reset. The following examples
set up the timers:

Timer0 will count to $AFAF, toggle its output, and reset back to $0000. This will continue infinitely until
the timer is disabled or a reset occurs. No interrupts are set. Prescale is set at 256 and the system clock is
divided by 16, therefore resolution is (16

×

(256))/70 MHz = 58.51us. Timeout period is

(16

×

256

×

44976)/70 MHz = 2.63s ($0 - $AFAF = 44976 decimal).

NOTE

The timers were initialized in the SIM to have interrupt values. The
following examples have the interrupts disabled. The initialization in the
SIM configuration was for reference. The Timers CANNOT provide
interrupt vectors, only autovectors.

Autovectors and ICRs have been set up as follows. The interrupt levels and priorities were chosen by
random for demonstrative purposes. Users should define the interrupt level and priorities for their specific
application.

11.6.5.1

Timer0 (Timer Mode Register)

Bits 15:8 sets the prescale to 256 ($FF)

Bits 7:6 set for no interrupt (“00”)

Bits 5:4 sets output mode for “toggle”. No interrupts(“10”)

Bits 3 set for “restart” (“1”)

Bits 2:1 set the clocking source to system clock/16 (“10”)

Bit 0 enables/disables the timer (“0”)

move.w #$FF2C,D0;Setup the Timer mode register (TMR0)

move.w D0,TMR1;

Bit 1 is set to 0 to disable the timer

move.w #$0000,D0; writing to the timer counter with any value resets it to zero

move.w D0,TCN1;

11.6.5.2

Timer0 (Timer Reference Register0)

The TRR register is set to $AFAF. The timer will count up to this value (TCN = TRR), toggle the “TOUT”
pin, and reset the TCN to $0000.

move.w #$AFAF,D0;Setup the Timer reference register (TRR0)

move.w D0,TRR1

Other registers used for TIMER 0

TCR0;TIMER0 Capture Register, 16-bit, R

TER0;TIMER0 Event Register, 8-bit, R/W

«
...
190
191
192
193
194
...
»

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды