manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 492

Universal Serial Bus Interface

MCF5253 Reference Manual, Rev. 1

24-30

Freescale Semiconductor

 

Address MBAR2 + 0x784

Access: User read/write

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

R

PTS

PTW

PSPD

PFSC PHCD WKOC WKDS WLCN

PTC

W

Reset

0

0

0

1

1

1

0

0

0

0

0

0

0

0

0

0

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

R

PO

PP

LS

PR

SUSP

FPR

OCC

OCA

PEC

PE

CSC

CCS

W

Clear

Clear

Clear

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

Figure 24-25. Port Status and Control (PORTSC) Register

Table 24-27. Port Status and Control (PORTSC) Register Field Descriptions

Field

Description

31–30

PTS

Port Transceiver Select. This register bit is used to control which parallel transceiver interface is selected.
00 On-Chip transceiver (UTMI+)
01 Reserved.
10 Reserved.
11 Reserved.
This bit is not defined in the EHCI specification.

29

Reserved.

28

PTW

Parallel Transceiver Width. This register bit is used to control the data bus width of the parallel transceiver interface. 
This bit defaults to 1 after reset and is read only.
0 8-bit interface—[60 MHz] UTMI+ interface.
1 16-bit interface—[30 MHz] UTMI+ interface.
PTW is valid only for UTMI mode (PTS = 00). 
This bit is not defined in the EHCI specification.

27–26

PSPD

Port Speed. This read-only register field indicates the speed at which the port is operating. 
This bit is not defined in the EHCI specification.
00 Full-speed
01 Low-speed
10 High-speed
11 Undefined

25

Reserved.

24

PFSC

Port Force Full-speed Connect. This bit is used to disable the chirp sequence that allows the port to identify itself as a 
HS port.
0 Allow the port to identify itself as High Speed.
1 Force the port to connect only at Full-speed.
This bit is not defined in the EHCI specification.

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды