manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 424

USB, ATA DMA, and Clock Integration Module

MCF5253 Reference Manual, Rev. 1

22-4

Freescale Semiconductor

 

22.2.5

USB/FlexCAN Clock Register (USBCANCLK)

22.3

Functional Description

22.3.1

ATA/USB Cache Memory

A 16 Kbytes local memory is put on a local bus, available as fast, local, memory to the ATA and USB 
modules. A block diagram of how the devices are tied to this local bus is given in 

Figure 22-5

.

Figure 22-5. ATA/USB Shared RAM Block Diagram

 Offset: MBAR2 0x510 (USBCANCLK)

Access: User read/write

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

R

CAN

CLK

USB

CLK

W

Reset 0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

1

Figure 22-4. USB/FlexCAN Clock Register (USBCANCLK)

Table 22-5. USB/FlexCAN Clock Register (USBCANCLK) Field Descriptions

Field

Description

31–2

Reserved, should be cleared.

1

CANCLK

FlexCAN clock gating.
0 FlexCAN clock disabled. The FlexCAN modules are placed in sleep mode and its interface is not available.
1 FlexCAN clock enabled.

0

USBCLK

USB clock gating.
0 USB clock disabled. When disabled, the USB is placed in standby mode, and only the USB resume interrupt will 

work. This interrupt will signal reception of USB resume condition on the USB bus. All other functions are not 
available.

1 USB clock enabled.

USB Controller

ATA Controller

ATA DMA

16 kB RAM

Arbiter

Controller

Inter

nal Bus

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды