manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 491

Universal Serial Bus Interface

MCF5253 Reference Manual, Rev. 1

Freescale Semiconductor

24-29

 

24.6.3.12 Configure Flag Register (CONFIGFLAG)

This EHCI register is not used in this implementation. A read from this register returns a constant of a 
0x0000_0001 to indicate that all port routings default to this host controller.

24.6.3.13 Port Status and Control Registers (PORTSC)

This register is reset only when power is initially applied or in response to a controller reset. The initial 
conditions of a port are:

•

No device connected

•

Port disabled

If the port has port power control, this state remains until the software applies power to the port by setting 
port power to one.

For the module in device mode, the controller does not support power control. Port control in device mode 
is used only for status port reset, suspend, and current connect status. It is also used to initiate test mode 
or force signaling and allows the software to put the PHY into low power suspend mode and disable the 
PHY clock.

Address MBAR2 + 0x780

Access: User read

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

R

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

R

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

Figure 24-24. Configure Flag (CONFIGFLAG) Register

Table 24-26. Configure Flag (CONFIGFLAG) Register Field Descriptions

Field

Name Description

31–0

–

Reserved. (0x0000_0001, all port routings default to this host)

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды