manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 387

Background Debug Mode (BDM) Interface

MCF5253 Reference Manual, Rev. 1

Freescale Semiconductor

20-17

 

Command Sequence:

Figure 20-14. Write Memory Location Command Sequence

Operand Data:

Two operands are required for this instruction. The first operand is a longword absolute address that 
specifies a location to which the operand data is to be written. The second operand is the data. Byte data 
is transmitted as a 16-bit word, justified in the least significant byte; 16- and 32-bit operands are 
transmitted as 16 and 32 bits, respectively.

Result Data:

Command complete status is indicated by returning the data $FFFF (with the status bit cleared) when the 
register write is complete. A value of $0001 (with the status bit set) is returned if a bus error occurs.

20.3.4.1.5

Dump Memory Block (DUMP)

DUMP is used in conjunction with the READ command to access large blocks of memory. An initial 
READ is executed to set up the starting address of the block and to retrieve the first result. The DUMP 
command retrieves subsequent operands. The initial address is incremented by the operand size (1, 2, or 

Write 
Memory 
Location

BERR

XXX

“Not Ready”

LS Addr

“Not Ready”

MS Addr

“Not Ready”

Read (B/W)

???

Next Cmd

Result

XXX

Data

“Not Ready”

“Not Ready”

Next Cmd

Write 
Memory 
Location

BERR

XXX

“Not Ready”

LS Addr

“Not Ready”

MS Addr

“Not Ready”

Write (Long)

???

Next Cmd

“Cmd Complete”

XXX

MS Data

“Not Ready”

“Not Ready”

Next Cmd

LS Data

“Not Ready”

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды