Notifier ID50 SERIES Скачать руководство пользователя страница 7

Страница: 7 / 94

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

997-263, Issue 4

September 2002

Introduction

1.1 Manual Purpose

This purpose of this manual is to provide the user with

all recommended procedures and full technical details

for the successful installation, commissioning and

programming of a NOTIFIER ID50 Series Panel.

The descriptions and procedures also apply to the

NOTIFIER ID60 panel. Differences between the ID50 and

ID60 panels are given in

Appendix 2

Procedures described in this manual include appropriate

warnings and cautions to guide the user towards adopting

safe and methodical work practices during the installation,

commissioning and programming phases.

Important Note

This manual must be read, and its content clearly

understood, before proceeding with any work relating to

the ID50 Series Panel. Damage to the control panel may

result from NOT following the recommended procedures

described in this manual.

This manual provides all necessary instructions for the

ID50 Series Panel and applies only to fire panels fitted

with compatible software.

CAUTION: In particular, care must be taken when

powering up/down any repeaters.

If there are any areas of doubt, consult your supplier

before continuing with the system installation,

commissioning and programming.

1.2 System Design and Planning

It is assumed that the system, of which the ID50 Series

Panel equipment is a part, has been designed by a

competent fire alarm system designer in accordance with

the requirements of EN54 Part 14 and any other local

codes of practice that are applicable.

The design drawings should clearly show the positions

of all the ID50 Series Panel control equipment and field

devices.

Содержание ID50 SERIES































































































Результаты поиска

Содержание ID50 SERIES

Отзывы:

Похожие инструкции для ID50 SERIES

Бренды по названию

Популярные бренды

Notifier ID50 SERIES, Инструкция по установке, пусконаладке и конфигурации

Результаты поиска

Содержание ID50 SERIES

Отзывы:

Похожие инструкции для ID50 SERIES

Бренды по названию

Популярные бренды