Notifier ID50 SERIES Скачать руководство пользователя страница 30

Страница: 30 / 94

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Commissioning

997-263, Issue 4

September 2002

4.3 Internal Checks

When all PCBs have been installed and all cabling has

been successfully checked, the appropriate jumper links

may need to be configured, as described below.

4.3.1 Jumper Link Options

SND Jumper (J7 / J6 / J8)

The SND Jumper link is the default position for the 6-way

link. Removing the link from the SND jumper disables

the normal operation of the outputs - for normal panel

operation this link should not be removed. The jumper is

situated to the left of the Loop terminal block (TB5) at the

top of the PCB.

ÜE Jumper (J12 / J10 / J11)

Not supported in standard operation.

Software Upgrade (J4)

The Software Upgrade Jumper in conjunction with the

Upgrade kit is used to upgrade the panel operating

software. To enable the panel upgrade, fit a link to J4

and connect the appropriate cable. The link J4 must be

removed on completion of the upgrade (see

997-415,

ID50 Series Panel - Upgrading Instructions

). This

jumper is situated to the right of the Digital/ÜE terminal

block (TB8).

Configuration Lock (J9)

The Configuration Lock Jumper is used to lock and unlock

the system configuration. If the link is fitted the system

configuration is locked and changes will NOT be allowed.

If the link is removed system configuration is possible.

The panel can only be configured with the Configuration

Lock (J9) in the unlocked position. The jumper is situated

to the left of the Digital / ÜE terminal block (TB8).

SND

ENABLED

DISABLED

J7 J6 J8

J1 SND / ÜE

MEM

FLASH PRG

ENABLE

FLASH PRG

ENABLE

ENABLED

LOCKED

DISABLED

UNLOCKED

Содержание ID50 SERIES































































































Результаты поиска

Содержание ID50 SERIES

Отзывы:

Похожие инструкции для ID50 SERIES

Бренды по названию

Популярные бренды

Notifier ID50 SERIES, Инструкция по установке, пусконаладке и конфигурации

Результаты поиска

Содержание ID50 SERIES

Отзывы:

Похожие инструкции для ID50 SERIES

Бренды по названию

Популярные бренды