background image

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Inst

allation Guide

12

997-263, Issue 4

September 2002

2.5.2 Removing the Panel Electronics

The ID50 Series Panel electronics comprises the PCB

assembly with mounted LCD unit and the mounted fascia.

These  are  supplied  as  one  spared  item  in  kit

PN: 020-635-XXX. This assembly is located within the

back box, but should ONLY be removed when installing

the back box or if the PCB requires replacement.

CAUTION: The electronic circuits of the ID50 Series

Panel use CMOS devices which can be damaged by

static discharge. Suitable precautions MUST be taken

when handling circuit boards.

Procedure

When installing the back box or, if it becomes necessary

to remove the PCB assembly for another reason, follow

this recommended procedure:

1

Remove  the  cover  and  store  in  a  safe  place,  see

Section 2.5.1, Removing the Cover

. Then make a

back-up  of  the  current  system  configuration,

remembering to disconnect the link at jumper J19.

Note:

The blade connection to the cover fitted in back

boxes incorporates a locking barb. To remove this

connection, pull the shroud (B), NOT the earth wire,

from the earth blade terminal (A).

2

Isolate the mains power supply and disconnect the

battery interlink wire if fitted.

3

At the two-part connector TB1 (on the PCB assembly),

using a constant pulling action carefully disconnect

the mains and battery power supply wiring.

4

Taking 

suitable anti-static precautions

 remove the

RS485 Interface PCB, if fitted (refer to 

Section 2.7.1,

Installing the RS485 Interface Module PCB

).

5

At  the  PCB  assembly,  note  the  polarity  and

connections of all cables and any jumper configuration

settings. Using a screwdriver, loosen all the connector

securing screws. Carefully secure all external cable

tails away from the electronics and from the back box.

6

Using a No. 1 Posidriv screwdriver, remove the eight

(8) M3 x 8mm clinch screws from the PCB assembly.

Gently lift the PCB assembly clear of the supporting

pillars, place it in an anti-static bag and store safely.

Note:

If the PCB is to be returned to the manufacturer

note its Serial Number and Revision Level (located

along one edge).

Содержание ID50 SERIES































































































Отзывы: