![background image](http://html1.mh-extra.com/html/nec/univerge-sv9100/univerge-sv9100_hardware-manual_3936970061.webp)
UNIVERGE SV9100
Issue 1.2
System Hardware Manual
2 - 21
AC240V Power Supply:
Dedicated 15 Amp circuit
Power Requirements: 230 VAC @ 15A Controlling/Base Chassis
Power Consumption: Base Chassis=263VA, Expansion
Chassis=263VA, total 1060VA
Input Voltage: 90VAC to 264VAC
(Rated Voltage: 100VAC/120VAC/220VAC/230-240VAC)
Frequency: 47Hz - 63Hz (Rated frequency: 50/60Hz)
Phase and Wire: Single Phase, 2 Line + PE Type
Grounding Requirements: No. 14 AWG copper wire
Feeding Voltage:
D
term
/OPX/DID: -48V
SLT: 25mA / -28V
With input voltage of 230 VAC and with full load conditions:
.
Base chassis can refer to either 9.5” or 19” chassis
Output Power: Base chassis=
130W
, Expansion chassis=
130W
, total
520W
AC Input I: Base chassis=
1.15A
, Expansion chassis=
1.15A
, total
4.6A
VA @ 230V: Base chassis=
276VA
, Expansion chassis=
276VA
, total
1104VA
KWh @ AC Input I x 230V/1000: Base chassis=0.276 KWh,
Expansion chassis=0.276 KWh, total 1.104 KWh
BTU (KWh x 3413): Base chassis=
942 BTU
, Expansion chassis=
942
BTU
, total
3768 BTU (at 240Vac)
A dedicated outlet, separately fused and grounded for each chassis
should be installed
5.2.2
Power Supply Consumption
Table 2-18 Power Consumption
Chassis
Maximum
RMS
Current
Watts Used
(Idle)
Watts Used
(Maximum)
Basic Chassis – GCD-CP10 Chassis
2.19 A
96
130
Double Pole/Neutral Fusing
(power supply fuses are located at both the L and N
side).
Содержание Univerge SV9100
