![background image](http://html1.mh-extra.com/html/nec/univerge-sv9100/univerge-sv9100_hardware-manual_3936970394.webp)
Issue 1.2
UNIVERGE SV9100
5 - 134
Installing DT Series Digital and IP Multiline Terminals
The DTL-8R-1 is limited to five RF channels. The RF channel is changed
automatically to find the best channel.
Depending on your environment, the maximum number of cordless devices used
without interference varies.
Multiple base and handset units should not be closer than 20 feet at any time.
Radio interference causes interruptions in conversation. When this happens, your unit
is not defective. When noise continues, move to a different location while you talk.
(You might even need to move the base unit.)
10.5 Selecting a Location
Select a location for the
D
term
Cordless DECT to avoid excessive heat or
humidity. The base unit of the
D
term
Cordless DECT can be placed on a desk
or tabletop near a standard 230 Vac outlet and telephone line jack. The base
unit can also be mounted on a standard wall plate using the wall mount
adapter. Keep the base unit and handset away from sources of electrical
noise (motors, fluorescent lighting, computers, PC monitor).
10.6 Installation Precautions
To ensure optimum performance follow these guidelines.
m
Each base unit must be placed at least 20 feet apart.
m
Always place the base unit on top of a desk or on higher shelves. Avoid
locations surrounded by metal surfaces.
m
Place the base away from any electrical component such as a PC,
monitor and other telephone.
10.7 Connecting the Telephone Cords
When connecting the telephone cords, observe the following precautions.
To connect the telephone cords:
m
Never install telephone wiring during a lightning
storm.
m
Never touch bare telephone wires or terminals unless
the telephone line is disconnected at the network
interface.
m
Use caution when installing or modifying telephone
lines.
Содержание Univerge SV9100
