Issue 1.2
UNIVERGE SV9100
4 - 8
Installing the SV9100 Blades
2.2.3.2
Installing GCD-PRTA (T1/PRI) Blades
The GCD-PRTA (T1/PRI) Interface blade uses the first block
of 30 consecutive trunks.
For example, if an GCD-4COTA and GPZ-4COTE blade is
installed for trunks 1~8, the GCD-PRTA (T1/PRI) blade
automatically uses trunks 9~32. If GCD-4COTA and
GPZ-4COTE blades are installed for trunks 1~8 and 17~24,
the GCD-PRTA (T1/PRI) blade uses trunks 25~54. The
GCD-PRTA (T1/PRI) blade cannot use trunks 9~16 (even if
available) since they are not part of a consecutive block of
30 trunks.
2.3
Remove an Extension or Trunk Blade
Any blade,
EXCEPT
the ones listed below can be removed while the system is
powered up. To remove any of the blades listed below, the system
must first
be powered down
.
GCD-CP10
GPZ-BS10
and
GPZ-BS11
GPZ-IPLE
To remove an extension/trunk blade with the system running:
1.
When LED 2 is extinguished, all extensions/trunks are idle.
2.
Loosen the thumb screws on either side of the blade and pull it out of the
chassis.
2.4
Uninstalling a Blade Slot Through Software
The installer can turn off (busy out) and delete (remove from software) blade
slots in the Controlling and Expansion Chassis in programming for port
renumbering or to replace it with a different blade. Deleting a blade may affect
blade slot programming capability. Refer to Program 90-05 in the Univerge
SV9100 Programming Manual for detailed programming information.
Содержание Univerge SV9100
