UNIVERGE SV9100
Issue 1.2
System Hardware Manual
4 - 55
5.1.2
Installation
Install the COIU blade into an available slot in the chassis. (Refer to
Figure 4-14 GCD-4COTA Blade on page 4-53
for a layout of the
blade.)
.
If the GPZ-4COTE is to be used, install this prior to inserting the
GCD-4COTA blade into the chassis.
5.1.3
LED Indications
LED indications for the GCD-4COTA are listed in
Table 4-27
GCD-4COTA LED Indications
. Each LED is listed with its associated
function and LED and Operational status. Refer to
Figure 4-14
GCD-4COTA Blade on page 4-53
for the location of the LEDs on the
blades.
Table 4-27 GCD-4COTA LED Indications
LED Indication
Operation Status
Remarks
Live LED
(Green)
Busy LED
(Red)
On
On
System Initializing
–
Flash (1s)
On
The assignment of the unit is refused.
When you exceed the system
capacity.
When the main software
version is not matched.
Flash (1s)
Trouble found during self-diagnostics.
–
Flash
(100ms)
On
Normal
Operation
A Channel is busy (use
another from CH1 ~ CHx).
–
Off
All channels are idle.
–
Off
On
Unit Busy
A Channel is busy (use
another from CH1 ~ CHx).
–
Off
All channels are idle.
–
Flash (100ms
On/Off)
Downloading firmware.
–
Содержание Univerge SV9100
