NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 54 / 198

Configuring Your System 3-21

Optional RAID Controller

Factory Installed Controller

One of the options available for your system is the dual channel Mylex AcceleRAID 250 (

NEC

SecuRAID 210)

Controller board, which gives your system the added security of fault tolerance.

If you order a system with the RAID controller, the system is pre-configured at the factory. Refer to

the “RAID Configurations” table to determine how the RAID controller was configured at the

factory. If you want to reconfigure disk arrays and logical drives, you must run the AcceleRAID

250 BIOS Configuration Utility; if you want to change the RAID level, you must run the Mylex

Disk Array Controller Utilities (DACCF) software. Refer to the AcceleRAID 250 documentation

included with your system for information on running the AcceleRAID250 BIOS Configuration

Utility and the DACCF Utility.

RAID Configurations

mber of Hard Drives

RAID Level
Configured

Hard Drives in
Array

Description

JBOD

JBOD (RAID 0) JBOD is an acronym for Just a Bunch Of Disks.

Each drive can operate independently as with a common host

bus adapter; or multiple drives may be spanned and seen as a

single very large drive. No redundancy is provided.

Mirroring (RAID 1) Drives are paired and mirrored. All data is

100% duplicated on an equivalent drive (fully redundant).

Striping with Parity (RAID 5) Data is striped across several

physical drives. Parity protection is used for data redundancy.

3 plus 1 hot spare

drive

Striping with Parity (RAID 5) Data is striped across three

physical drives. Parity protection is used for data redundancy.

This drive is used as the “Hot Spare.”

The first four disks are as stated above; the remaining disks are

not part of the array, but are ready to be configured.

Add-on Controller

If you are adding the RAID controller to an existing system, the AcceleRAID™ 250 BIOS

Configuration Utility allows you to configure disk arrays and logical drives in your system. Since

the utility resides in the AcceleRAID™ 250 BIOS on the RAID controller, its operation is

independent of the operating system in your server. Refer to Chapter 4 in this User’s Guide for

information on installing an add-in option board. Refer to Chapter 4 of the AcceleRAID™ 250

Installation Guide for information on running the AcceleRAID™ 250 BIOS Configuration Utility.

Note:

Next Boot Status for the first Symbios SYM53C875 controller must be

turned

OFF

if you install the optional Mylex AcceleRAID 250 Controller board in

your system. Refer to “Symbios Configuration Utility” found earlier in this chapter.

DACCF Configuration Utility

The DACCF utility is included with the RAID controller. The AcceleRAID™ 250 supports various

versions of RAID technology (referred to as RAID levels). To use any RAID level, you must

configure the RAID controller using the DACCF Configuration Utility prior to installing your

Network Operating System. For an explanation of this utility, refer to the

Disk Array Controller

Configuration Utilities Manual

that was shipped with the controller. Chapter 2 (

Preparing the

Array)

covers array hardware preparation, configuration, and initialization. After completing the

steps in Chapter 2, you can install your Network Operating System.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды