NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 64 / 198

4-4

Upgrading Your System

Removing a Side Panel

To install options in your system, you must remove the side panel on the left side of the system (as

viewed from the front). The side panel on the right side of the system (as viewed from the front)

only has to be removed when adding removable media devices. The right side panel removes in

the same manner as the left side panel.

CAUTION

For proper cooling and airflow, do not operate the system with the side panels

removed. Always replace the panels before powering on the system.

WARNING

If you are removing the side panel after the system is set up, you must first power off

the system and all external devices.

Unplug

the system power cord

To remove a side panel:

Power off the system and ensure it is disconnected from the ac wall outlet.

The side panel is secured to the chassis with three screws. Remove the screws securing the side

panel. Save the screws for reattaching the side panel.

Slide the side panel toward the rear of the chassis. This unlocks the locking fingers behind the

side panel.

Pull the side panel up and away from the chassis.

Removing a System Side Panel

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды