NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 39 / 198

3-6

Configuring Your System

Primary/Secondary IDE Master and Slave Submenu

Feature

Choices

Description

Your Setting

Type

Auto

None

CD-ROM

User

Auto allows the system to attempt auto-detection of

the drive type.

None informs the system to ignore this drive.

CD ROM allows the manual entry of some fields

described below.

User allows the manual entry of all fields described

below.

Cylinders

0 to 65535

Number of cylinders on drive. This field is

changeable only for Type User.

Heads

1 to 16

Number of read/write heads on drive. This field is

changeable only for Type User.

Sectors

0 to 63

Number of sectors per track. This field is

changeable only for Type User.

Maximum Capacity

N/A

Computed drive size. This field is informational

only for Type User.

Multi-Sector Transfer

Disabled

2, 4, 8, or 16 sectors

Determines the number of sectors per block for

multi-sector transfers. This field is informational

only for Type Auto.

LBA Mode Control

Disabled

Enabled

Enabling LBA causes logical block addressing to be

used in place of cylinders, heads, and sectors.

This

field is informational only for Type Auto.

32 Bit I/O

Disabled

Enabled

Enabling allows 32 bit IDE data transfers.

Transfer Mode

Standard

Fast PIO 1

Fast PIO 2

Fast PIO 3

Fast PIO 4

FPIO 3/DMA 1

FPIO 4/DMA 2

Selects the method for moving data to and from the

drive.

This field is informational only for Type

Auto.

Ultra DMA Mode

Disabled

Mode 0

Mode 1

Mode 2

Selects the Ultra DMA Mode for moving data to

and from the drive.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды