NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 52 / 198

Configuring Your System 3-19

Changing the Adapter and Device Configurations

The SCSI Configuration Utility Main Menu lists the onboard SCSI adapter and shows its current

settings. The adapter controls the operation of the SCSI devices in your system (hard disk drives or

removable media devices).

Select “Adapter Setup” and press

ENTER

. The Adapter Setup screen displays.

Adapter Setup Screen

Description

Recommended Setting or Display
Only

Your Configuration

SCAM Support

Parity

Host SCSI ID

Scan Order

Low to High

Removable media support

None

CHS Mapping

SCSI Plug and Play Mapping

Highlight the function you want to change and press

ENTER

. You will be prompted to save

changes when you exit the configuration utility.

To change device configuration parameters, perform the following steps:

At the SCSI Configuration Utility Main Menu, select “Device Selections” and press

ENTER

The Devices 0 to 7 screen displays.

Select the SCSI device you are reconfiguring and press

ENTER

. If you are configuring SCSI

Hard Disk Drives, refer to the "SCSI Hard Disk Drives" Table below; if you are configuring

SCSI Removable Media Devices, refer to the "SCSI Removable Media Devices" Table below for

recommended settings.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды