NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 173 / 198

C-8

Emergency Management Port Console

Status Bar

The status bar displays at the bottom of the current window. It contains the following status

information:

SERVER NAME

: the name of the server (stored in the Phonebook) connected to.

LINE

: the type of line connection. This would be either direct or modem.

MODE

: either Redirect of EMP, depending on whether the EMP has control of the COM 2 port.

LINE STATUS

: gives status information on the server connection. For example, if a server is

connected, the status bar says "Connected." Otherwise, the line is blank.

EMP Console Main Menu

File



Exit

- Exits the EMP.

Connect



Disconnect

- disconnects the server connection.



[Re]Connect - raises the connect dialog.



A list of the five most recent connections - can click on one of the five servers most recently

connected to. A connection to the selected server is initiated.

Action



Power On/Off

- powers the server on or off with post-power-up options.



Reset

- resets the server with post-reset options.



SEL Viewer

- opens the SEL viewer.



SDR Viewer

- opens the SDR viewer.



FRU Viewer

- opens the FRU viewer.



Phonebook

- opens the phonebook dialog.

Help -

provides version information and help topics for the EMP.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды