NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 31 / 198

2-10

Setting Up the System

Connecting the Power Cord

Plug the female end of the AC power cord into the input receptacle on the rear of the power supply

cage. Plug the male end of the power cord into NEMA 5-15R outlet for 100-120 VAC or NEMA 6-

15R outlet for 200-240 VAC.
If the power cord supplied with the system is not compatible with the AC wall outlet in your

region, obtain a suitable power cord that meets the following criteria.

The power cord must be rated for the available AC voltage and have a current rating that is at

least 125% of the current rating of the system.

The power cord connector that plugs into the wall outlet must be terminated in a grounding-

type male plug designed for use in your region. It must have certification marks showing

certification by an agency acceptable in your region.

The power cord connector that plugs into the system must be an IEC- type CEE-22 female

connector.

The power cord must be less than 1.8 meters (6.0 feet) long.

WARNING

Your system shipped with a power cord. Do not attempt to modify or use the

supplied AC power cord if it is not the exact type required.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды