NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 119 / 198

5-10

Problem Solving

Incorrect or No Beep Code

Check the following:

Is the speaker enabled?

Is the speaker cable connected to the system board?

If the system operates normally, but there was no beep, the speaker may be defective, contact your

service representative for assistance.
Record the beep code emitted by POST, and see the “Messages and Beep Codes”

section found

later in this chapter.

No Characters Appear on Screen

Check the following:

Is the keyboard working? Check to see if the

Num Lock

light is functioning.

Is the video display monitor plugged in and turned on?

Are the brightness and contrast controls on the video monitor properly adjusted?

Are the video monitor switch settings correct?

Is the video monitor signal cable properly installed?

Is the onboard video controller enabled?

If you are using an option video controller board, perform the following:

Verify that the video controller board is fully seated in the system board connector.

Run the SSU to disable the onboard video controller.

Reboot the system for changes to take effect.

If there are still no characters on the screen after you reboot the system, contact your service

representative or authorized dealer for assistance.
POST emits one long beep and two short beeps pattern to indicate a possible problem with the

video display controller. If you do not receive a beep pattern and characters do not display, the

video display or video controller may have failed. Contact your service representative or

authorized dealer for assistance.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды