NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 83 / 198

Upgrading Your System 4-23

Hard Disk Drives

Your system supports a variety of optional IDE or SCSI hard disks. Contact your sales

representative or dealer for a list of approved devices. The internal hard disk drives are located in

the 3.5-inch drive bay.

3.5-Inch Drive Bay Locations

If you are adding or removing an IDE hard disk device, consider the following:

The system board supports a primary and secondary IDE channel connector. Each of these

supports two devices, for a total of four IDE devices.

A first (master) device and a second (slave) device are supported on both the primary and

secondary IDE connector. The device configuration, master versus slave, is determined by

jumpers on the device. Cable Sense (CS) device configuration is not supported.

Your system comes with a three-connector IDE cable connecting the CD-ROM and an optional

IDE device (either tape or the third hard disk) to the system board secondary connector. The

CD-ROM that comes with your system is set as the master device and the optional device is set

as the slave device on this connector.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды