NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 120 / 198

Problem Solving 5-11

Characters are Distorted or Incorrect

Check the following:

Are the brightness and contrast controls properly adjusted on the video display? Refer to the

documentation supplied with your video display.

Are the video monitor signal and power cables properly installed?

If the problem persists, the video monitor may be faulty or it may be the incorrect type. Contact

your service representative for assistance.

System Cooling Fan Does Not Rotate

Note

The system has a cooling fan module behind the hard disk drives. In

addition, there is a cooling fan that is an integral part of the power supply. There are

no serviceable components inside the power supply. If the power supply is opened,

the manufacturer's warranty is voided.

Check the following:

Is AC power available at the wall outlet?

Is the system power cord properly connected to the system and the AC wall outlet?

Is the power connector for the cooling fan connected to the system board?

Is the front panel power on indicator lit?

If the switches and connections are correct and the power outlet is functioning, the power supply

has probably failed. Contact your service representative for assistance.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды