NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 121 / 198

5-12

Problem Solving

Diskette Drive Activity LED Does Not Light

Check the following:

Are the diskette drive power and signal cables properly installed?

Is the diskette drive properly configured?

Is the diskette drive activity light always on? If so, the signal cable may be plugged in

incorrectly.

If you are using the onboard diskette controller, use Setup or the SSU to make sure that Onboard

Floppy is set to Enabled. Conversely, to use an optional fixed/diskette controller, make sure that

Onboard Floppy is set to

Disabled

. For information about running Setup or the SSU, refer to the

“Configuring Your System” chapter.
If the problem persists, there may be a problem with the diskette drive, system board, or drive

signal cable. Contact your service representative for assistance.

Hard Disk Drive Activity LED Does Not Light

If you have installed one or more hard disk drives in your system, check the following:

Are the power and signal cables to the drive properly installed?

Are all relevant switches and jumpers on the hard drive and adapter board set correctly?

Is the hard disk drive properly configured in the SSU?

Run the SSU to make sure that the hard disk drive is configured with the correct parameters. For

information about running the SSU, refer to the “Configuring Your System” chapter.
If the problem persists, there may be a problem with the hard disk drive, the optional controller

board, system board, drive signal cable, or LED connector. Contact your service representative for

assistance.

Note:

The hard disk drive activity light on the front panel lights when a hard

disk drive, or a SCSI device controlled by the onboard SCSI host controller, is in use.

This LED does not display CD-ROM activity.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды