NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 49 / 198

3-16

Configuring Your System

Hard Drive Submenu

For options on this menu, use the up or down arrow keys to select a device, then press the <+> or

<-> keys to move the device higher or lower in the boot priority list.

Option

Description

1. Hard Drive #1 (or actual

drive string)

IDE drives will have a suffix attached to the drive ID string:

PM - hard drive on Primary Master Channel

PS - hard drive on Primary Slave Channel

SM - hard drive on Secondary Master Channel

SS - hard drive on Secondary Slave Channel

SCSI CD-ROMs will be displayed here because the onboard Symbios SCSI bios treats CD-ROMs as hard drives.

SCSI removable drives will also appear here.

2. Other Bootable Device

Covers all the boot devices that are not reported to the system BIOS through the BIOS boot specification

mechanism. This includes all PCI cards that are not bios boot compliant (legacy) as well as ISA cards that are not

PnP compliant.. ISA legacy cards will boot first before non bios boot compliant PCI cards (in scan order from

lowest slot to highest).

Removable Devices

For options on this menu, use the up or down arrow keys to select a device, then press the <+> or

<-> keys to move the device higher or lower in the boot priority list.

Option

Description

1. Legacy Floppy Drive

Refers to the onboard 3.5” floppy drive.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды