NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 145 / 198

System Cabling A-3

Standard Configuration

Your system is cabled using a dual channel on-board IDE Controller and an on-board Symbios

Logic SYM53C875 SCSI Controller. The on-board IDE controller supports the internally mounted

CD-ROM as its first (master) device and an optional IDE device as its second (slave) device. The

SCSI controller attaches to a 68-pin 16-bit (wide) SCSI connector interface and is capable of

supporting a maximum of four 1-inch high SCSI hard disk drives or three 1.6-inch high SCSI hard

disk drives. Also, a 3.5-inch diskette drive is installed in all systems and interfaces separately to the

system board.
Referring to the "IDE Disk System Cable Configuration" Figure, your system can be cabled using

the on-board dual enhanced IDE controller. This controller has two connectors (primary and

secondary) on the system board, each connector supporting a first (master) and a second (slave)

device. This provides support for the internally mounted IDE CD-ROM, an optional tape, and up

to three internally mounted IDE hard disk drives. An IDE cable (K) connects the secondary IDE

connector to the CD-ROM as its master device (I) and an optional IDE device as its slave device (J).

Another IDE cable (O) connects the primary IDE connector to the optional first hard drive (HD1) as

its master device (M) and the optional second hard drive (HD2) as its slave device (N).
As an option, the on-board SCSI controller can be used to control a SCSI tape drive. In this case, a

SCSI cable (D) connects the wide SCSI connector to the optional SCSI tape drive (B) via a narrow

SCSI to wide SCSI adapter (C). The tape drive SCSI address assignment is 2. SCSI termination must

be installed in the last SCSI drive of the daisy chain cabling. Since the tape is the only SCSI device,

the termination resistors (A) are installed in the tape drive.
When adding or removing IDE devices, consider the following:

The system board supports a primary and secondary IDE channel connector. Each of these

supports two devices, for a total of four IDE devices.

A first (master) device and a second (slave) device are supported on both the primary and

secondary IDE channel connector.

The device configuration, master versus slave, is determined by jumpers on the devices. Cable

Sense (CS) device configuration is not supported.

If only one device is on a channel connector it must be set as the master device.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды