NEC EXPRESS 5800 ES1400 SERIES Online Скачать руководство пользователя

Страница: 144 / 198

A-2

System Cabling

This appendix contains information and procedures on cabling configurations used in your

system. The configurations include:

Standard Configuration

RAID Configuration.

Before You Begin

WARNING

The DC push-button on/off switch on the front panel does not turn off the system

AC power. Also, +5vdc is present on the system board whenever the AC power cord

is connected between the system and an AC outlet. Before doing the procedures in

this manual, make sure that your system is powered off and unplug the AC power

cord from the back of the chassis. Failure to disconnect power before opening your

system can result in personal injury and equipment damage.

Static Precautions

An electrostatic discharge (ESD) can damage disk drives, option boards, and other components.

You can provide ESD protection by wearing an antistatic wrist strap attached to chassis ground

when handling system components.
Electronic devices can be easily damaged by static electricity. To prevent damage, keep them in

their protective packaging when they are not installed in your system.

Содержание EXPRESS 5800 ES1400 SERIES Online







































































































































































































Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды

NEC EXPRESS 5800 ES1400 SERIES Online, Онлайн руководство по обслуживанию

Результаты поиска

Содержание EXPRESS 5800 ES1400 SERIES Online

Отзывы:

Похожие инструкции для EXPRESS 5800 ES1400 SERIES Online

Бренды по названию

Популярные бренды