MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 86 / 173

•

Lubricate the valve guide.

•

Fit the circlips.

•

Press a punch with the valve guides.

•

Use a reamer to bore the holes the

valve stems slide through so that the

inside diameter is at the prescribed val-

ue. The interference between the seat

on the head and the valve guide must

be 0.046 - 0.075 mm (0.0018 - 0.0030

in)

VALVE AND GUIDES COUPLING DATA CHART (INLET)

Specification

Desc./Quantity

Valve guide inside diameter mm (in)

8.000 - 8.022 (0.3150 - 0.3158)

Valve stem diameter

7.972 - 7.987 (0.3139 - 0.3145)

Fitting clearance mm (in)

0.013 - 0.050 (0.0005 - 0.0020)

VALVE AND GUIDES COUPLING DATA CHART (OUTLET)

Specification

Desc./Quantity

Valve guide inside diameter mm (in)

8.000 - 8.022 (0.3150 - 0.3158)

Valve stem diameter mm (in)

7.965 - 7.980 (0.3136 - 0.3142)

Fitting clearance mm (in)

0.025 - 0.057 (0.0010 - 0.0022)

Checking the cylinder head

Check that:

•

The planes of contact with the cover and with the cylinder are not scored or damaged so as

to compromise a perfect seal.

•

Check that the clearance between the valve guide holes and valve stanchions is within the

prescribed limits.

•

Check the status of the valve seats.

The valve seats should be reamed with a mill. The

seat inclination angle is 45° +/- 5'. After milling, it

is necessary to grind them to ensure a good cou-

pling and a perfect sealing between the ring nuts

and the valve heads.

Engine

California EV V1100

ENG - 86

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды