MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 104 / 173

Removing

The oil pump used is of the gear type and takes

the motion from the crankshaft via a chain.

•

Drain all the engine oil.

•

Remove the alternator.

•

Remove the engine pinion, the timing

system gear and the oil pump gear to-

gether with the timing chain.

•

Remove the chain tensioner.

•

Unscrew and remove the screws.

•

10pt; FONT-FAMILY: Arial; mso-fare-

ast-font-family: "Times New Roman";

mso-ansi-language: IT; mso-fareast-

language: IT; mso-bidi-language: AR-

SA">Remove the oil pump.

See also

Replacement
Removing the generator

Chain removal

Inspection

If any defects are found due to the pump control:

- Height of the gears that should be within 15.973 - 16.000 mm (0.629 - 0.630 in);

- Height of the seats on the pump casing should be within 16.032 - 16.075 mm (0.631 - 0.633 in);

If these parts are not within those values they must be replaced.

Engine

California EV V1100

ENG - 104

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды