MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 122 / 173

•

Remove the locking ring inside the

sleeve using a thin screwdriver.

CAUTION

BE CAREFUL NOT TO DAMAGE THE SLEEVE RIM.

•

Remove the stem from the wheel hold-

er sleeve together with the seal ring (1),

the cap (2), the upper bushing on the

fork leg (3), the lower bushing (4) on

the tube.

NOTE

WHEN REMOVING THE STEM FROM THE WHEEL HOLD-
ER SLEEVE SOME PARTS MAY REMAIN INSIDE THE
SLEEVE. IF THIS OCCURS, THESE PARTS MUST BE RE-
MOVED AFTERWARDS, BEING CAREFUL NOT TO DAM-
AGE THE SLEEVE RIM AND THE UPPER BUSHING SEAT

•

Slide off the pumping member unit

from the holding tube.

•

Remove the bottom buffer it could be

remained mounted in the wheel holder

fork leg, in this case, remove it from its

inside.

Suspensions

California EV V1100

SUSP - 122

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды