MOTO GUZZI California EV V1100 Скачать руководство пользователя страница 108

Страница: 108 / 173

Removing

The electrical fuel pump unit consists of following:

- electrical pump (1);

- fuel filter (2);

- pressure adjuster (3);

- collapse protection pre-filter (4);

- fuel level control sensor (5).

It is recommended to properly clean the system

when disassembling and fitting the piping and the

components.

•

Set to the ignition switch to OFF.

•

Remove the front saddle.

•

Remove the tank.

•

Undo and remove the fixing screws of

the fuel pump flange.

•

Slide off and remove the electrical fuel

pump unit.

WHEN REMOVING THE PUMP UNIT MAKE

SURE NOT TO DAMAGE THE PIPES AND THE FUEL LEVEL
SENSOR..

See also

Fuel tank

Checking

<span style="FONT-SIZE: 12pt; FONT-FAMILY:

"Times New Roman"; mso-fareast-font-family:

"Times New Roman"; mso-ansi-language: IT;

mso-fareast-language: IT; mso-bidi-language:

AR-SA">If the collapse protection pre-filter shows

traces of sediment, clean it with a jet of com-

pressed air, directing it so that impurities do not

enter in its inside.

See also

Removing

Power supply

California EV V1100

P SUPP - 108

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Бренды по названию

Популярные бренды