MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 110 / 173

coming out from the nozzle (atomization), forming

a cone of about 30°.

Resistance value: 12 ohm.

If you want to perform an electrical test in the in-

jector, apply a maximum voltage of 6V, for very

limited periods.

Removal:

•

Remove the throttle body.

•

Undo the two retainer screws and re-

move the electro-injector unit.

Removing the throttle body

The amount of intake air is determined by the opening of the throttle valve located at the beginning of

the intake manifold of each cylinder.

The air required for the operation at idle speed passes through a by-pass channel, equipped with a

adjuster screw: turning this screw, the amount of air varies, which is introduced in the manifold and

consequently also the pace of idle speed.

A second screw, allows the correct adjustment of the throttle valve closure, to avoid jamming with the

surrounding duct; said screw should not be used to adjust the idle.

Removal:

•

Remove the air box filter.

•

Disconnect from the throttle body:

- The wiring harness of the potentiometer;

- the wiring harness on the injectors;

- the throttle grip transmission;

- the starter for transmission control;

- The fuel intake and return pipes;

•

Loosen the clamps securing the engine and remove the throttle body from the engine.

CLOG

THE DUCTS OF THE INTAKE MANIFOLD TO PREVENT FOREIGN BODIES TO ENTER THE COM-
BUSTION CHAMBER.

Co rate adjustment

•

Remove the saddle.

•

Remove the left fairing.

Power supply

California EV V1100

P SUPP - 110

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды