MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 134 / 173

WHEEL AXLE

Check the amount of distortion of the wheel axle:

Turn the pin on a surface plate and check with a

feeler gauge the maximum value of the distortion

•

Service limit 100 mm (3.94 in): 0.2 mm

(0.0079 in)

WHEELS

Having established the good condition of the bear-

ings, it is necessary to verify the rim operating as

follows:

•

Visually check for any deformations,

ruts and cracks: if there are, replace

the rim;

•

Insert the pin into the wheel and place

it on two fixed matching parts;

•

Install a dial gauge supporting it in or-

der to detect the values of lateral devi-

ation and eccentricity of the wheel rim

relative to the axis of the pin.

CAUTION

The lateral deviation and actual eccentricity is half of the
total reading of the measuring instrument.
Standard values:

•

Lateral deviation: 0.5 mm (0.020 in)

•

Eccentricity: 0.8 mm (0.031 in)

•

Serviceability limit: 2 mm (0.079 in)

•

If the values do not fall within the limit it is nec-
essary to replace the rim.

Rear wheel

Rimozione

CALIFORNIA EV (1997-2000)

Chassis

California EV V1100

CHAS - 134

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды