MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 100 / 173

MAIN JOURNAL DIAMETER ON THE TIMING SYSTEM SIDE (A)

Specification

Desc./Quantity

Main journal regular production

37.975 mm (1.49507 inch)
37.959 mm (1.49444 inch)

CRANKPIN DIAMETER (B)

Specification

Desc./Quantity

Regular production

44.008 - 44.020 mm - (1.73259 - 1.73307 in)

Undersized diameter: 0.254 mm (0.01000 in)

43.754 - 43.766 mm (1.72259 - 1.72307 in)

Undersized diameter: 0.508 mm (0.02000 in)

43.500 - 43.512 mm (1.71259 - 1.71307 in)

Undersized diameter: 0.762 mm (0.03000 in)

43.264 - 43.258 mm (1.70330 - 1.70307 in)

FLYWHEEL SIDE MAIN JOURNAL DIAMETER (C)

Specification

Desc./Quantity

Regular production

52.970 mm (2.08542 inch)
53.951 mm (2.12405 inch)

WEIGHT CONTROL FOR CRANKSHAFT BALANCING

The weight of the connecting rods together with screws must be balanced.

A difference of 4 grams (0.14 oz) is permissible.

To balance the crankshaft from a static point of view, it is necessary to apply the following weight on

the crank pin: 1810 g (63.84 oz).

Checking the connecting rod

CONNECTING RODS

When examining the connecting rods, check that:

•

Bushing conditions and bushings-pins clearance;

•

Shaft parallelism;

•

Connecting rod bearings.

These are thin shell bearings, anti-friction alloy that does not allow for any adaptation; replace them

immediately if seizing or wear marks are found.

Upon replacing the bearings it may be necessary to ream the crankshaft pin.

Before reaming the crankpin, measure the pin diameter comparing it with the maximum wear allowed,

as indicated in the figure; this defines what kind of undersizing the bearing should have and to which

diameter the pin should be reamed.

Checking shaft parallelism

Check shafts for squaring before fitting them.

It is therefore necessary to check that the head holes and the connecting rod small end are parallel and

on the same plane.

The maximum parallelism and plane error of the two shafts of the head and rod small end, measured

at 200 mm (7.873 inch) should be +/- 0.10 mm (0.00393 inch).

Engine

California EV V1100

ENG - 100

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды