GearTronic ZERO GT3100-K1 / GT3100-K2 / GT3100-K3
User Manual – v1.0 – 01/12/16
IMPORTANT: All models (except ZX10R) identify the gear by calculating the ratio between speed and engine revs because these
motorbike don't have a gear position sensor. The device therefore displays the gears when the vehicle is running with the clutch
released.
IMPORTANT: All PZRacing products are water resistant but not waterproof, do not wash the product under water jet pressure, the
product could be irreparably damaged.
Installation
Display installation
The main unit must be positioned so that it can be clearly seen. Once the ideal position has been found the unit can be fitted using the special adhesive
material supplied in the box (degrease the surface and leave the adhesive for at least 24 hours) or by using the two supplied screws to the two holes at the
back of the device.
Connection
Find the mating 4 poles connector on your bike, normally you can find it near the electronic central unit ECU under the seat
.
Remove the cap and connect the GearTronic ZERO to the diagnostic connector, fix the cable along its length.
Note for ZX10-R: on this motorcycle there are two identical connectors, the correct one have the wires below: green/black, green,
black/yellow, brown/white.
Use
Turning on/off the device
GearTronic ZERO works completely automatically, the switching on and off of the device will operate using the key of the bike.
Calibration
GearTronic ZERO for Kawasaki models doesn't require any calibration
, simply connect the plug
(Default Mode)
;
just in case some
gears are not well recognized
follow the instruction to set the indicator
(Custom Mode)
Note: the touch screen is capacitive, so must be used without gloves.
“Custom Mode”
1- Turn on the key and the engine in “Neutral”
2- Tap the display three times repeatedly to enter calibration mode
3- The display scrolls all the colors for backlight (A:Red, B:Green, C:Blue, D:Orange, E:Violet, F:Light Blue); tap the display to confirm the color
4- The display shows the number “1” blinking, insert the first gear, release the clutch and keep the engine revs around 4/5000 rpm constantly
5- After 5 seconds the display shows the number “2” blinking, insert the second gear and keep the engine revs around 4/5000 rpm constantly
6- Continue in this way for all the gears of your vehicle
7- GearTronic ZERO will automatically stop the setup procedure showing two alternate circles on the top and bottom of the display, will switch to
standard visualization showing the gear inserted
Note: GearTronic automatically stops the calibration procedure if the speed decrease between the gears, so chooose your preferred
engine revs and use it for any gear, in this way the speed will always increase.
Restore “Default Mode”
1- Turn on the vehicle but NOT the engine.
2- Tap the display three times repeatedly to enter calibration mode
3- The display scrolls all the colors for backlight (A:Red, B:Green, C:Blue, D:Orange, E:Violet, F:Light Blue); tap the display to confirm the color
4- The display shows the number “1” blinking, just wait the next step in few seconds
5- The display shows “D” (Default), default mode is succesfully restored.
Changing colour background
To change colour of background repeat only the first 3 point of the “Custom Mode” set up procedure and then switch off the gear indicator.
Troubleshooting
In the case of incorrect gears rerun your set-up making sure to maintain a constant engine revs after insertion of the gear.
If you experience any problems with the installation or operation of this product, please consult our dedicated product page at
www.pzracing.it, where you will find all relevant information relating to the resolution of any major issues. If the problem cannot
be solved please send an email to our customer service department at [email protected]
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: +39 0721 820434 – Email: [email protected]
