MOTO GUZZI California EV V1100 Скачать руководство пользователя страница 141

Страница: 141 / 173

Removing

Checking

Sleeve for transmission shaft and bevel pinion

(1).

The inner splines must be intact; free from grain or

dents, otherwise replace it.

Transmission shaft Seeger rings (2)

Check that the rings are not cracked or have lost

elasticity, otherwise replace them.

Cardan shaft (3)

The splines on the cardan shaft must be intact,

free from grain or dents.

Check that the joint is not hardened or too loose,

otherwise replace it.

See also

Removing

Bevel gears

Removing

•

Remove the rear wheel.

•

Drain the oil from the transmission box.

•

Undo and remove the four nuts.

•

Remove the transmission box.

•

Detach the casing (1) from the box

complete with the pinion (2) with gas-

ket (OR) (3).

California EV V1100

Chassis

CHAS - 141

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Бренды по названию

Популярные бренды