MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 111 / 173

•

Connect a vacuum gauge to the sockets on the intake manifolds.

•

Connect the diagnostic tool AXONE, using the specific cable to the diagnostic socket, and

to the battery of the motorcycle (not an external battery).

•

Always connect first the positive terminal and then the negative one.

•

Turn on the AXONE device by pressing the button 'ON / OFF'

•

With the side arrows go to the menu "self diagnosis".

CAUTION

TO ACCESS

THE SELF DIAGNOSIS FUNCTIONS IT IS NECESSARY THAT THE OBD MODULE IS FITTED ON
THE BACK OF AXONE.

•

In the following screens select: the mo-

torcycle brand (MOTOGUZZI), model,

engine, type of system (software of the

injection system), leading digits of the

chassis, type of electronic control unit

fitted.

•

Turn the ignition key to "ON", AXONE

will connect to the control unit.

•

Select the throttle valve potentiometer

parameter.

•

Remove the dipstick (1) of the left side

throttle body by loosening the lock ring

(2).

•

On the left throttle body, using the

throttle adjustment dowel (3), adjust

the throttle potentiometer to 3.6° (+/-

0.1°) readable on AXONE.

USE A WRENCH TO ACT ON THE ADJUST-

MENT DOWEL (3).

California EV V1100

Power supply

P SUPP - 111

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды