MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 87 / 173

Installing the valves

NOTE

THE FOLLOWING OPERATIONS REFER TO REMOVING ONLY ONE HEAD BUT APPLY TO BOTH
HEADS.

•

Place the valve (6) inside the head.

•

Place the lower cap (5) and the shim-

ming washers.

•

Place the outer spring (4).

•

Place the inner spring (3).

•

Insert the upper cap (2).

•

Place the two cotters (1) on the seats

in the valves.

•

By compressing the spring with the

special tool of the valve, fit the valve

cotters.

Specific tooling

10.90.72.00

Tool for valve removal and refitting

•

Remove the special tool

Timing

California EV V1100

Engine

ENG - 87

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды