MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 58 / 173

Flexible coupling caps on the clutch shaft

It does not require any verification, only check that the inner grooves are smooth.

Flexible coupling springs on the clutch shaft

Check that they are not deformed or have lost elasticity, otherwise replace them.

Sleeve with couplings on the clutch shaft

Check that the inner grooves are smooth and that the coupling surface has no excessive wear.

Transmission gear bearing on the clutch shaft

It shall not show excessive consumption or grain on the teeth. The contact surface of the teeth and the

inner grooves must be smooth, otherwise replace the gear.

Checking the forks

Check that the forks work area are well levelled and are not worn, so as to have lost the toughening

characteristics and that the nose-pieces operating in the drum splines are not excessively worn, oth-

erwise replace the forks.

Checking the gearbox

Gearbox and cover

The gearbox and the cover shall not show cracks in no point; the cover crankcase coupling surfaces

are not scored or damaged; the thread of the hub caps shall not be stripped.

Sealing rings

The seal rings, normally, if removed from their seats, they must be replaced, this is to be sure of their

perfect fit.

Ball and roller bearings

The bearings must be in perfect condition. The balls or rollers must be intact and smooth on their entire

surface.

Assembling the gearbox

After several checks, inspections and replacements, reassemble the gearbox operating as follows:

Fitting of bearings on the gearbox and on the cover

Warm up the gearbox and the cover before the fitting to a temperature of about 150 - 160 °C (302 - 320

°F)

As a first step carefully clean the seats and the bearing rings with solvent (trichlorethylene). Then with

a brush spread a thin layer of "Loctite" on the periphery of the outer ring of the bearing, in the seats of

the gearbox and cover, where the bearings have to be put.

Pay attention that the "Loctite" does not go between the balls or rollers of the bearings.

The bearings to be mounted with "Loctite" are the following:

- Bearing for clutch shaft on the housing.

Engine

California EV V1100

ENG - 58

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды