MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 75 / 173

•

The second clutch plate.

•

The pressure plate disc cover.

•

The pressure plate disc with springs.

Checking the clutch plates

OPTION 01

Driven plate

Check that the surfaces touching the crown gear and the inner disc are perfectly smooth and even,

otherwise replace it.

Inner disc

Check that the support surfaces are perfectly smooth and even, otherwise replace them.

OPTION 02

Driven plates

Check that the supporting surfaces with the driven plates are perfectly smooth and even and that the

external toothing that works inside the flywheel is not damaged, otherwise, replace the plate.

California EV V1100

Engine

ENG - 75

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды