MOTO GUZZI California EV V1100 Скачать руководство пользователя

Страница: 29 / 173

•

Check oil level by means of the oil dip-

stick.

•

The oil level is correct when it close to

the "MAX" mark.

MAX

= maximum level

MIN = minimum level

Add engine oil if required:

•

Unscrew and remove the cap with dip-

stick.

•

Top-up with engine oil until it goes

above the minimum level marked

"MIN".

CAUTION

DO NOT ADD ADDITIVES OR ANY OTHER SUBSTANCE TO THE FLUID. WHEN USING A FUNNEL
OR ANY OTHER ELEMENT, MAKE SURE IT IS PERFECTLY CLEAN.

Replacement

Use an engine oil type with characteristics indicated in the table of recommended products.

The other viscosity levels indicated in this table can be used if the average temperature of the motor-

bike's area of use is within the indicated range.

NOTE

HOT OIL IS MORE FLUID AND WILL DRAIN OUT MORE EASILY AND COMPLETELY.

•

Place a container with 4000 cm³ (244

cu.in) capacity under the drainage

plug.

•

Unscrew and remove the drainage

plug.

California EV V1100

Maintenance

MAIN - 29

Содержание California EV V1100














































































































































































Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды

MOTO GUZZI California EV V1100, Руководство по обслуживанию станции

Результаты поиска

Содержание California EV V1100

Отзывы:

Похожие инструкции для California EV V1100

Бренды по названию

Популярные бренды