ON-BOARD DIAGNOSTIC [AIR BAG SYSTEM]
T–219
T
Diagnostic procedure
End Of Sie
STEP
INSPECTION
ACTION
1
INSPECT CRASH ZONE SENSOR
•
Check following PID/DATA monitor, using
SST
(WDS or equivalent).
(See
T–195 PID/DATA MONITOR TABLE
)
— OD_F_CRSH
•
Is crash zone sensor normal?
Yes
Present malfunction diagnosis:
•
Replace SAS unit.
(See
T–124 SAS UNIT REMOVAL/INSTALLATION
)
Past malfunction diagnosis:
•
Troubleshooting completed.
No
Go to next step.
2
INSPECT WIRING HARNESS BETWEEN
CRASH ZONE SENSOR AND SAS UNIT
Warning
•
Handling air bag system components
improperly can accidentally deploy air
bag modules and pre-tensioner seat
belts, which may seriously injure you.
Read AIR BAG SYSTEM SERVICE
WARNINGS before handling air bag
system components.
(See
T–117 SERVICE WARNINGS
)
•
Turn ignition switch to LOCK position.
•
Disconnect negative battery cable and wait
for
more than 1 minute
.
•
Remove column cover.
•
Disconnect clock spring connector.
•
Remove glove compartment.
•
Disconnect passenger-side air bag module
connector.
•
Disconnect driver and passenger-side side
air bag module connectors. (Vehicle with
side air bag)
•
Disconnect driver and passenger-side
curtain air bag module connectors. (Vehicle
with curtain air bag)
•
Remove B-pillar lower trim. (Vehicle with pre-
tensioner seat belt)
•
Disconnect driver and passenger-side pre-
tensioner seat belt connectors. (Vehicle with
pre-tensioner seat belt)
•
Turn up floor covering.
•
Disconnect all SAS unit connectors.
•
Disconnect crash zone sensor connector.
•
Connect negative battery cable.
•
Inspect following wiring harnesses between
SAS unit and crash zone sensor terminals
for short to ground, short to power supply,
and open circuit:
— 1B—A
— 1C—B
•
Is wiring harness okay?
Yes
Replace crash zone sensor, then go to next step.
(See
T–123 CRASH ZONE SENSOR REMOVAL/
INSTALLATION
)
No
Replace wiring harnesses.
3
INSPECT SAS UNIT
•
Turn ignition switch to LOCK position.
•
Disconnect negative battery cable and wait
for
more than 1 minute
.
•
Connect all SAS unit connectors.
•
Connect crash zone sensor connector.
•
Is DTC B2296 indicated?
Yes
Present malfunction diagnosis:
•
Replace SAS unit.
(See
T–124 SAS UNIT REMOVAL/INSTALLATION
)
Past malfunction diagnosis:
•
Troubleshooting completed.
No
Troubleshooting completed.
Содержание 6 2002
