Lenze I/O system 1000 Скачать руководство пользователя страница 56

Страница: 56 / 583

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

Configuring the I/O system in the »PLC Designer«

4.3

Mapping the real station structure in the »PLC Designer«

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

4.3.3

Configuring I/O modules on the EtherCAT bus coupler module

The following step-by-step instructions describe the manual mapping of the available station

layout in the

device view

of the »PLC Designer«.



Tip!

When an online connection has been established to the Lenze Controller, you can also start

an automatic search for available devices via fieldbus scan by executing the

Start Search

command in the

context menu

of the EtherCAT master after adding the EtherCAT master

(step 3).



Note!

Observe the following conditions before creating an EtherCAT configuration in the »PLC

Designer«:

• Only

I/O compound modules EPM-Sxxx from hardware version 1B

are supported.

• The sequence of the EtherCAT slaves in the

device view

must correspond to the

physical arrangement of the EtherCAT topology.

• In order that the system works properly, do not use any end terminals when setting

up the system configuration in the

device view

• Select the cycle times according to the technical data, from 1 ... 10 ms.

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды

Lenze I/O system 1000, Справочное руководство

Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды